• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Installing a cat flap might appear daunting, but it is fairly simple to install with the right instructions. Decide how high you'd like your cat flap to be (normally it's located at belly height). Then, mark this area on your door and then use the included template to guide you when drilling.

If you have a kitten that is still a newborn, gently prop the door slightly open and invite it to go through. Reward it when it goes through.

Measure the Door

A cat flap is an excellent method to let your pet leave and come into and out of your home whenever it pleases. This will help keep your cat healthy by making sure that it is getting exercise and also being able to go back inside if stuck outside in bad weather, particularly in winter. This can reduce the time you spend letting your cat in or out and make your home safer by letting you know when it's gone.

It is essential to make sure that the cat flap is set up correctly to stop your pet from being forced through it or escaping by other animals (e.g. dogs). It is crucial to determine the height of your pet's belly and the entrance to your home to ensure that the flap is at the proper height. If your cat is larger or cat flap fitting shorter than the average, you can adjust the flap's position by moving it up or down a small amount.

The next step is to use a spirit level to mark the center of the door that you will be installing the flap. Then, using the markings as an indication, cut out the form of your flap on the door with the help of a jigsaw. After cutting the area out then sand the edges to create smooth surfaces. Drill any holes you need to.

The process of installing a cat flap is not as difficult as you think and it should not take more than two hours to complete the entire job from start to completion. The process can be slightly more complicated if you are required to install it in the case of a uPVC door or a composite one. This is due to the fact that these doors come in a variety of thicknesses, which could affect the way the holes are cut. We always suggest to consult with an expert if this is your first time working with glass.

Measure Your Cat

You can save yourself hours of ignoring the pet's meow to be let in or out. This is especially helpful for cats that are inside during the winter months while you work.

If you're planning to put a cat flap inside your door, it is essential to take measurements of your cat prior to attempting the task. Although it might seem like to be a simple task, it is essential to measure the right way or your pet will find it difficult to use.

First, make sure that your cat is calm before taking measurements. You'll need to keep your cat in a place where they cannot move. Also, make sure that the measuring tape is straight and not bent against their body. You can get an accurate measurement by keeping the measuring tape or the ruler flat against the body of the animal from the top to the bottom.

Once you've figured out the measurements of your cat, it is time to look at the door and decide where to put the flap. It is advisable to place the flap at the height of your cat's stomach as this will help them to pass through it without too much effort. This will also stop the flap from making a lot of noise as it swings back and forward.

You should consider the thickness of the uPVC or composite door, as well. While all timber doors have a similar thickness, uPVC or composite doors can differ greatly in their overall design. This can make the installation of a flap for your cat more difficult, as you have to make sure that the hole is the right size.

It is also worth reading through the directions included with the kit to find a template drawing that can be used to mark the location of the hole in the door. This will allow you determine where the opening needs to be and ensure that the template is correctly positioned on the door. Using a spirit-level to check that the template is in a straight line against the door can prove beneficial.

Cut the Flap

You will need to cut a hole in the door panel to install your cat flap before you can put it in place. This can be a tricky job and it is recommended to seek the help of a professional cat flap fitting service for this job in case you don't have the skills or experience to complete the task yourself. You can also refer to the instructions included in the kit to find out how to do it properly.

To do this, you will need to determine the height of your cat or kitten's belly and use this as a reference point. As a rule of thumb put the flap approximately 10-15 centimeters above the ground. This is the typical height of the belly for cats. This will allow your cat to move through the flap without difficulty and make it difficult for other cats or naughty neighbours to get inside or out.

Once you have determined the best location for the cat flap to be positioned, mark this location on the door using a pencil. Next, if your kit comes with a paper template, lay this over the door and use the marks to drill holes in every corner of the template. Then, you should be able to cut out the template and replace it with the flap for cats.

If you are installing your cat flap in upvc door panel flap inside the form of a door made of wood or uPVC, it is possible to do it yourself if are comfortable with a Jigsaw. Be careful not to cut through the mullions or rails that run vertically of your door. You can use a jigsaw to cut the panel into a circle or square, depending on the design of your cat flap. Be patient and don't try to force the jigsaw into cutting faster.

Once the hole has been made, carefully place the cat flap in its new place of residence. Make sure that it is securely secured. If the flap has screw caps, push them onto the protruding bolts. After the screws are installed smooth the edges and seal any gaps. This will prevent the entry of draughts into your home.

Fit the Flap

If you have a simple cat flap, you can leave it open and encourage your pet to use it by putting a small amount of cat food in front of the door. Alternatively you can try pushing the cat through using your hands or with a stick. Once your cat is used to walking through the flap it should be able to go in and out as it wishes so you can let it in or out without having to be there holding the door open to allow it in all day (and likely in all weather conditions).

It is possible to put a cat flap in the replacement upvc door panel with cat flap doors with cat flap or glass door, but it's not as simple as installing one on a wooden external door. This is because UPVC doors and some types of glass doors don't have a uniform thickness. This could have a significant impact on how you cut the hole for the flap and can also affect whether your flap fits correctly once it's been put in place.

The mounting kit may contain a template that outlines where to drill holes. If the kit does not include a template, you are able to make one by yourself. When cutting, it's important to not push the jigsaw far enough to make a larger hole than you need in your door.

Some cat flaps are available in circular designs, which are more difficult to install. If you have a circular flap, make sure the hole is located in the correct place on the door. If not, your cat might not be able use it, and may be locked outside for the entire day (or at night).

Some models of cat flap have locks that let you control when your cat comes and goes. These are useful for pets who are afraid of going out in the dark, or coming back to the house at night. They are also useful for those who work all day. The lock can be turned on to allow or deny entry, and some can be locked in both directions, permitting you to close the door completely. This is particularly beneficial for sick or elderly cats who aren't keen on going out in rainy weather.